|
Trapezoidal thread forms are screw thread profiles with trapezoidal outlines. They are the most common forms used for leadscrews (power screws). They offer high strength and ease of manufacture. They are typically found where large loads are required, as in a vise or the leadscrew of a lathe. Standardized variations include multiple-start threads, left-hand threads, and self-centering threads (which are less likely to bind under lateral forces). The original trapezoidal thread form, and still probably the one most commonly encountered worldwide, is the Acme thread form ( ). The Acme thread was developed sometime in the second half of the nineteenth century as a profile well suited to power screws that has various advantages over the square thread, which had been the form of choice until then. It is easier to cut via either single-point threading or die than the square thread is (because the latter's shape requires tool bit or die tooth geometry that is poorly suited to cutting); it wears better than square (because the wear can be compensated for); it is stronger than a comparably sized square thread; and it makes for smoother engagement of the half nuts on a lathe leadscrew than square does.〔, (p. 30 ).〕〔, (pp. 176–177 ).〕 The trapezoidal metric thread form is similar to the Acme thread form, except the thread angle is 30°.〔(Trapezoidal coarse thread )〕〔(Trapezoidal fine thread )〕 It is codified by DIN 103.〔.〕 Although metric screw threads are generally more prevalent worldwide than imperial threads, the Acme thread is very common worldwide, and may be more widely used than the trapezoidal metric thread. This is not surprising, as manufacturers today are usually capable of making whichever threads (metric or imperial) are best for any given application (based on customer expectations or tooling availability). It may be that the tooling for Acme threads has been so dominant (compared to trapezoidal metric) that customers tend to want Acme threads for power screws regardless of metric standards used elsewhere in the product. ==Acme thread characteristics== The Acme thread form has a 29° thread angle with a thread height half of the pitch; the apex (or ''crest'') and valley (or ''root'') are flat. This shape is easier to machine (faster cutting, longer tool life) than is a square thread. The tooth shape also has a wider base which means it is stronger (thus, the screw can carry a greater load) than a similarly sized square thread. This thread form also allows for the use of a split nut, which can compensate for nut wear. The line of General Purpose (GP) Acme threads (ASME/ANSI B1.5-1988) are not designed to sustain external radial loads and both the nut and bolt are, ideally, independently supported, the nut by a linear guide and the screw by shaft bearings. This is due to the need to avoid "wedging" of the thread flanks when subjected to radial loads, which would contribute substantially to friction forces and thread wear. However, there is a centralizing Acme-thread standard (also specified in ASME/ANSI B1.5-1988) which caters to applications where the threads are not radially supported, where the roots and crests of opposing threads are designed to come into contact before the flanks do, under radial loads. This adds the requirement that the sum of the allowances and tolerances on the major diameters of nut and bolt be less than the sum of the allowances on the pitch diameters (PD); the drawback is that, for a given amount of end play (axial clearance, due solely to PD deviations), closer tolerances and cleaner work environment are necessitated in the application of a centralizing Acme thread. Compared to square threads, disadvantages of the Acme thread form are lower efficiency due to higher friction and some radial load on the nut (angular offset from square).〔 When created prior to 1895, Acme screw threads were intended to replace square threads and a variety of threads of other forms used chiefly for the purpose of traversing motion on machines, tools, etc. Acme screw threads are now extensively used for a variety of purposes. Long-length Acme threads are used for controlled movements on machine tools, testing machines, jacks, aircraft flaps, and conveyors. Short-length threads are used on valve stems, hose connectors, bonnets on pressure cylinders, steering mechanisms, and camera lens movement. The thread form shown in the figure is called ''basic''; the actual thread heights on both the internal (nut) and external (bolt) threads differ from ''P''/2 by the difference between two ''allowances'' (or ''clearances''): * A root-crest clearance between opposing threads of 0.01-in. minimum evenly-distributed clearance for 10 or less threads-per-inch pitches, 0.005-in. for finer pitches (this is also true for the minor diameters of the centralizing Acme thread, though not its major diameters, where the allowance is made less than the PD allowance) * A PD allowance, small compared to the first in the case of the GP and external centralizing Acme threads, but greater in the case of the internal centralizing Acme thread. The net effect is that the minimum thread heights are greater than basic for the internal and external GP and for the external centralizing, and the maximum height is shorter than basic for the internal centralizing Acme threads. The maximum diameter (within tolerance) at the crest of the screw threads, called the ''max major diameter of external thread'', is that of the basic thread form and equals the "nominal diameter," ''D'', stated in the screw's designation; the minimum diameter (within tolerance) at the crest of the nut thread, called the ''min minor diameter of internal thread'', is that of the basic thread form and equals the nominal diameter minus twice the basic thread height (i.e. ''D - P''). Finally, there also exists a stub Acme-thread standard, identical in all respects to the one just described ''except'' for the height of the basic thread being 0.3''P''. 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「trapezoidal thread forms」の詳細全文を読む スポンサード リンク
|